Dedicated to the research and development of hydraulic system components, providing services to over 100000 enterprises.
-
Service
-
Analysis of the Reasons for the Weak Reverse Power of Hydraulic Cycloid Motor
2025-04-16 11:36
1、 Internal malfunction of cycloidal motor
1. Internal sealing failure and excessive leakage of the cycloidal motor caused by poor manufacturing quality or improper use;
2. Friction between the motor rotor and pump bearings leads to increased vibration, resulting in excessive wear of the gear pump and affecting the normal operation of the cycloidal motor reverse rotation;
3. The internal wear of the cycloidal motor is excessive, and the power transmission inside the gear is not smooth, resulting in weak reverse force.
2、 Hydraulic system malfunction
1. There is damage or blockage in the hydraulic oil pipeline of the hydraulic system, which affects the normal flow of oil and the inlet and outlet of the gear pump;
2. Insufficient oil pump pressure or excessive air bubbles in the oil cylinder prevent the cycloidal motor from receiving sufficient hydraulic power during reverse rotation;
3. Oil leakage occurs in the hydraulic system, causing the hydraulic cylinder to malfunction and rendering the cycloidal motor powerless to reverse.
3、 Electrical control system malfunction
1. The electrical control system has malfunctioned, causing the machine to be unable to reverse or unable to reverse;
2. Damage to the control limit switch or transmission rod causes the cycloidal motor to malfunction in its original position;
3. Overloading of the motor power supply or mismatch between the control system and the power system can also cause the cycloidal motor to reverse and become powerless.
For the possible reasons mentioned above, the following troubleshooting and handling can be carried out:
1. Check whether the internal seal of the cycloidal motor is intact, identify leakage points, and repair or replace parts;
2. Check and adjust the pressure, flow rate, and quality in the hydraulic system, clean the pipelines in a timely manner, replace or repair damaged components, and maintain system stability;
3. Check the electrical control system, identify the fault points, and promptly carry out maintenance and replacement;
4. Through comprehensive analysis, develop a reasonable troubleshooting plan, carry out repair and maintenance, and ensure the normal reverse rotation of the hydraulic cycloidal motor.
【 Conclusion 】 There are many possible reasons for the weak reverse rotation of hydraulic cycloidal motors, and careful troubleshooting and analysis are needed to find the most suitable solution. At the same time, regular inspection and maintenance of hydraulic cycloidal motors can prevent malfunctions and ensure the normal operation of mechanical equipment.
Recommend reading
Gerotor Motor Abnormal Vibration: Cavitation, Bearing Damage and Assembly Error
This article summarizes gerotor motor abnormal vibration causes including hydraulic cavitation, bearing fatigue wear and assembly centering errors. It delivers practical identification methods, standardized correction skills and universal maintenance standards for field troubleshooting.
Gerotor Motor Low Output Torque Fault Analysis and On-site Inspection
This paper analyzes gerotor motor low-torque faults, introduces zero-tool field detection, and verifies solutions with sweeper and tiller practical cases.
Pressure Cannot Be Built Up After Installing New Multi-way Valve | Circuit & Component Check
This guide covers universal new multi-way valve no-pressure faults, standardized troubleshooting steps, and practical solutions verified with ZD102, ZDa15, ZSL118 real cases.
Multi-way Valve Heat Generation: Causes, On-site Judgment and Improvement Measures
This article analyzes multi-way valve overheating mechanisms, provides no-tool field judgment methods, distinguishes different heat-generating faults, and offers practical improvement schemes with real equipment cases.
Multi-way Valve External Oil Leakage Troubleshooting and Seal Replacement Guide
This guide covers multi-way valve external leakage identification, seal selection, standard replacement steps and real equipment repair cases for field maintenance.
Hydraulic Valve Internal Leakage Simple Test Method Without Professional Tools
This blog introduces 5 zero-tool field tests for hydraulic valve internal leakage, with detailed tables and real cases for fast on-site fault diagnosis.
Online Message
We will contact you within one working day. Please pay attention to your email.
Address
No. 215 Jianhua South Street, Yuhua District, Shijiazhuang City, Hebei Province, China